libreboot/docs/future/dumps/t500log/flashrom_write.log

flashrom v0.9.8-r1889 on Linux 3.13.0-39-lowlatency (i686)
flashrom is free software, get the source code at http://www.flashrom.org

flashrom was built with libpci 3.2.1, GCC 4.8.2, little endian
Command line (7 args): flashrom -V -p internal:laptop=force_I_want_a_brick -w ../t500recipe.rom -c MX25L3205D/MX25L3208D
Calibrating delay loop... OS timer resolution is 1 usecs, 789M loops per second, 10 myus = 11 us, 100 myus = 100 us, 1000 myus = 1013 us, 10000 myus = 10017 us, 4 myus = 6 us, OK.
Initializing internal programmer
No coreboot table found.
Using Internal DMI decoder.
DMI string chassis-type: "Notebook"
Laptop detected via DMI.
DMI string system-manufacturer: "LENOVO"
DMI string system-product-name: "224397G"
DMI string system-version: "ThinkPad T500"
DMI string baseboard-manufacturer: "LENOVO"
DMI string baseboard-product-name: "224397G"
DMI string baseboard-version: "Not Available"
========================================================================
WARNING! You seem to be running flashrom on an unsupported laptop.
Laptops, notebooks and netbooks are difficult to support and we
recommend to use the vendor flashing utility. The embedded controller
(EC) in these machines often interacts badly with flashing.
See the manpage and http://www.flashrom.org/Laptops for details.

If flash is shared with the EC, erase is guaranteed to brick your laptop
and write may brick your laptop.
Read and probe may irritate your EC and cause fan failure, backlight
failure and sudden poweroff.
You have been warned.
========================================================================
Proceeding anyway because user forced us to.
Found chipset "Intel ICH9M" with PCI ID 8086:2919.
Enabling flash write... Root Complex Register Block address = 0xfed1c000
GCS = 0x380461: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x1 (SPI)
Top Swap: not enabled
0xfff80000/0xffb80000 FWH IDSEL: 0x0
0xfff00000/0xffb00000 FWH IDSEL: 0x0
0xffe80000/0xffa80000 FWH IDSEL: 0x0
0xffe00000/0xffa00000 FWH IDSEL: 0x0
0xffd80000/0xff980000 FWH IDSEL: 0x0
0xffd00000/0xff900000 FWH IDSEL: 0x0
0xffc80000/0xff880000 FWH IDSEL: 0x0
0xffc00000/0xff800000 FWH IDSEL: 0x0
0xff700000/0xff300000 FWH IDSEL: 0x4
0xff600000/0xff200000 FWH IDSEL: 0x5
0xff500000/0xff100000 FWH IDSEL: 0x6
0xff400000/0xff000000 FWH IDSEL: 0x7
0xfff80000/0xffb80000 FWH decode enabled
0xfff00000/0xffb00000 FWH decode enabled
0xffe80000/0xffa80000 FWH decode enabled
0xffe00000/0xffa00000 FWH decode enabled
0xffd80000/0xff980000 FWH decode enabled
0xffd00000/0xff900000 FWH decode enabled
0xffc80000/0xff880000 FWH decode enabled
0xffc00000/0xff800000 FWH decode enabled
0xff700000/0xff300000 FWH decode disabled
0xff600000/0xff200000 FWH decode disabled
0xff500000/0xff100000 FWH decode disabled
0xff400000/0xff000000 FWH decode disabled
Maximum FWH chip size: 0x400000 bytes
SPI Read Configuration: prefetching disabled, caching enabled, 
BIOS_CNTL = 0x01: BIOS Lock Enable: disabled, BIOS Write Enable: enabled
SPIBAR = 0xb76e8000 + 0x3800
0x04: 0xe008 (HSFS)
HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=1, SCIP=0, FDOPSS=1, FDV=1, FLOCKDN=1
Warning: SPI Configuration Lockdown activated.
Reading OPCODES... done
0x06: 0x3f04 (HSFC)
HSFC: FGO=0, FCYCLE=2, FDBC=63, SME=0
0x50: 0x00001a1b (FRAP)
BMWAG 0x00, BMRAG 0x00, BRWA 0x1a, BRRA 0x1b
0x54: 0x00000000 FREG0: Warning: Flash Descriptor region (0x00000000-0x00000fff) is read-only.
0x58: 0x03ff0200 FREG1: BIOS region (0x00200000-0x003fffff) is read-write.
0x5C: 0x01f50001 FREG2: Warning: Management Engine region (0x00001000-0x001f5fff) is locked.
0x60: 0x01f701f6 FREG3: Gigabit Ethernet region (0x001f6000-0x001f7fff) is read-write.
0x64: 0x01ff01f8 FREG4: Platform Data region (0x001f8000-0x001fffff) is read-write.
Not all flash regions are freely accessible by flashrom. This is most likely
due to an active ME. Please see http://flashrom.org/ME for details.
0x74: 0x9fff03e0 PR0: Warning: 0x003e0000-0x01ffffff is read-only.
0x84: 0x81ff81f8 PR4: Warning: 0x001f8000-0x001fffff is locked.
Writes have been disabled for safety reasons. You can enforce write
support with the ich_spi_force programmer option, but you will most likely
harm your hardware! If you force flashrom you will get no support if
something breaks. On a few mainboards it is possible to enable write
access by setting a jumper (see its documentation or the board itself).
0x90: 0x04 (SSFS)
SSFS: SCIP=0, FDONE=1, FCERR=0, AEL=0
0x91: 0x000000 (SSFC)
SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=0, SME=0, SCF=0
0x94: 0x5006     (PREOP)
0x96: 0x143b     (OPTYPE)
0x98: 0x05200302 (OPMENU)
0x9C: 0x0601209f (OPMENU+4)
0xA0: 0x00000000 (BBAR)
0xC4: 0x00002005 (LVSCC)
LVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20, VCL=0
0xC8: 0x00002005 (UVSCC)
UVSCC: BES=0x1, WG=1, WSR=0, WEWS=0, EO=0x20
0xD0: 0x00000000 (FPB)
OK.
The following protocols are supported: FWH, SPI.
Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: probe_spi_rdid_generic: id1 0xc2, id2 0x2016
Found Macronix flash chip "MX25L3205D/MX25L3208D" (4096 kB, SPI) mapped at physical address 0xffc00000.
Chip status register is 0x00.
Chip status register: Status Register Write Disable (SRWD, SRP, ...) is not set
Chip status register: Bit 6 is not set
Chip status register: Block Protect 3 (BP3) is not set
Chip status register: Block Protect 2 (BP2) is not set
Chip status register: Block Protect 1 (BP1) is not set
Chip status register: Block Protect 0 (BP0) is not set
Chip status register: Write Enable Latch (WEL) is not set
Chip status register: Write In Progress (WIP/BUSY) is not set
This chip may contain one-time programmable memory. flashrom cannot read
and may never be able to write it, hence it may not be able to completely
clone the contents of this chip (see man page for details).
Write/erase is not working yet on your programmer in its current configuration.
Aborting.
Restoring MMIO space at 0xb76eb8a0
Restoring PCI config space for 00:1f:0 reg 0xdc