K3D-VOSTOK/OCTOPUS_PRO_cfg/prn_stepper_YL.cfg

#   YL_CS       PC6     DRIVE2
#   YL_DIR      PG3     DRIVE2
#   YL_STEP     PF11    DRIVE2
#   YL_ENABLE   PG5     DRIVE2
#   YL_DIAG2    PG10

[stepper_y]
step_pin:                       PF11
dir_pin:                        PG3
enable_pin:                     !PG5
rotation_distance:              39.7        # ?
microsteps:                     256
full_steps_per_rotation:        200         # for 0.9° motors - 400
#gear_ratio:
#   The gear ratio if the stepper motor is connected to the axis via a
#   gearbox. For example, one may specify "5:1" if a 5 to 1 gearbox is
#   in use. If the axis has multiple gearboxes one may specify a comma
#   separated list of gear ratios (for example, "57:11, 2:1"). If a
#   gear_ratio is specified then rotation_distance specifies the
#   distance the axis travels for one full rotation of the final gear.
#   The default is to not use a gear ratio.
#step_pulse_duration:
#   The minimum time between the step pulse signal edge and the
#   following "unstep" signal edge. This is also used to set the
#   minimum time between a step pulse and a direction change signal.
#   The default is 0.000000100 (100ns) for TMC steppers that are
#   configured in UART or SPI mode, and the default is 0.000002 (which
#   is 2us) for all other steppers.
endstop_pin:                    ^PG10
position_min:                   0           # ?
position_endstop:               404         # !!!
position_max:                   407         # !!!
homing_speed:                   50
homing_retract_dist:            5
second_homing_speed:            5
#homing_positive_dir:
#   If true, homing will cause the stepper to move in a positive
#   direction (away from zero); if false, home towards zero. It is
#   better to use the default than to specify this parameter. The
#   default is true if position_endstop is near position_max and false
#   if near position_min.

[tmc5160 stepper_y]
cs_pin:                         PC6
#   The pin corresponding to the TMC5160 chip select line. This pin
#   will be set to low at the start of SPI messages and raised to high
#   after the message completes. This parameter must be provided.
#spi_speed:                      100000
spi_bus:                        spi1
#spi_software_sclk_pin:          PA5
#spi_software_mosi_pin:          PA7
#spi_software_miso_pin:          PA6
#   See the "common SPI settings" section for a description of the
#   above parameters.
#chain_position:
#chain_length:
#   These parameters configure an SPI daisy chain. The two parameters
#   define the stepper position in the chain and the total chain length.
#   Position 1 corresponds to the stepper that connects to the MOSI signal.
#   The default is to not use an SPI daisy chain.
interpolate:                    False
#   If true, enable step interpolation (the driver will internally
#   step at a rate of 256 micro-steps). The default is True.
run_current:                    1.4         # (1.8)  Imax / squart(2) * 80%; Imax = Irms / squart(2)
#   The amount of current (in amps RMS) to configure the driver to use
#   during stepper movement. This parameter must be provided.
#hold_current:                   0.7         # ~~ run_current/2
#   The amount of current (in amps RMS) to configure the driver to use
#   when the stepper is not moving. Setting a hold_current is not
#   recommended (see TMC_Drivers.md for details). The default is to
#   not reduce the current.
sense_resistor:                 0.075
#   The resistance (in ohms) of the motor sense resistor. The default
#   is 0.075 ohms.
stealthchop_threshold:          999999
#   The velocity (in mm/s) to set the "stealthChop" threshold to. When
#   set, "stealthChop" mode will be enabled if the stepper motor
#   velocity is below this value. The default is 0, which disables
#   "stealthChop" mode.
#driver_MSLUT0: 2863314260
#driver_MSLUT1: 1251300522
#driver_MSLUT2: 608774441
#driver_MSLUT3: 269500962
#driver_MSLUT4: 4227858431
#driver_MSLUT5: 3048961917
#driver_MSLUT6: 1227445590
#driver_MSLUT7: 4211234
#driver_W0: 2
#driver_W1: 1
#driver_W2: 1
#driver_W3: 1
#driver_X1: 128
#driver_X2: 255
#driver_X3: 255
#driver_START_SIN: 0
#driver_START_SIN90: 247
#   These fields control the Microstep Table registers directly. The optimal
#   wave table is specific to each motor and might vary with current. An
#   optimal configuration will have minimal print artifacts caused by
#   non-linear stepper movement. The values specified above are the default
#   values used by the driver. The value must be specified as a decimal integer
#   (hex form is not supported). In order to compute the wave table fields,
#   see the tmc2130 "Calculation Sheet" from the Trinamic website.
#driver_MULTISTEP_FILT: True
#driver_IHOLDDELAY: 6
#driver_TPOWERDOWN: 10
#driver_TBL: 2
#driver_TOFF: 3
#driver_HEND: 2
#driver_HSTRT: 5
#driver_FD3: 0
#driver_TPFD: 4
#driver_CHM: 0
#driver_VHIGHFS: 0
#driver_VHIGHCHM: 0
#driver_DISS2G: 0
#driver_DISS2VS: 0
#driver_PWM_AUTOSCALE: True
#driver_PWM_AUTOGRAD: True
#driver_PWM_FREQ: 0
#driver_FREEWHEEL: 0
#driver_PWM_GRAD: 0
#driver_PWM_OFS: 30
#driver_PWM_REG: 4
#driver_PWM_LIM: 12
#driver_SGT:                     0
#driver_SEMIN: 0
#driver_SEUP: 0
#driver_SEMAX: 0
#driver_SEDN: 0
#driver_SEIMIN: 0
#driver_SFILT: 0
#driver_DRVSTRENGTH: 0
#driver_BBMCLKS: 4
#driver_BBMTIME: 0
#driver_FILT_ISENSE: 0
#   Set the given register during the configuration of the TMC5160
#   chip. This may be used to set custom motor parameters. The
#   defaults for each parameter are next to the parameter name in the
#   above list.
#diag0_pin:
#diag1_pin:                      ^!PG10
#   The micro-controller pin attached to one of the DIAG lines of the
#   TMC5160 chip. Only a single diag pin should be specified. The pin
#   is "active low" and is thus normally prefaced with "^!". Setting
#   this creates a "tmc5160_stepper_x:virtual_endstop" virtual pin
#   which may be used as the stepper's endstop_pin. Doing this enables
#   "sensorless homing". (Be sure to also set driver_SGT to an
#   appropriate sensitivity value.) The default is to not enable
#   sensorless homing.